Dr. Valdes-Morales, Hector

2017, Dr. Valdes-Morales, Hector, Chaouki, Zineb, Khalil, Fouad, Ijjaali, Mustapha, Rafqah, Salah, Sarakha, Mohamed, Zaitan, Hicham

This article presents a combination of coagulation–flocculation and powder activated carbon (PAC) adsorption as a treatment process for landfill leachate. Leachates were collected from a municipal solid waste landfill in Mediouna site, Casablanca city. Ferric chloride (FeCl3) is used here as a coagulant to study the optimum conditions for the removal of chemical oxygen demand (COD), colour, total suspended solids (TSS) and turbidity in jar tests. This coagulant showed the highest removal efficiency in terms of COD (62.5%), turbidity (92.5%), colour (80%) and least sludge volume generation (30% v/v) for an optimum coagulant dose of 12 g Fe3+ L–1. Combining coagulation with adsorption process onto PAC enhances the removal of COD, turbidity and colour reduction by a 77%, a 99% and a 99.7%, respectively. These results show that coagulation-adsorption could be used as a promising hybrid process for the treatment of landfill leachates.

2016, Dr. Valdes-Morales, Hector, Zaitan, Hicham, Mohamed, Elham, Nawdali, Mostafa, Rafqah, Salah, Manero, Marie

A great number of pollution problems come as a result of the emission of Volatile Organic Compounds (VOCs) into the environment and their control becomes a serious challenge for the global chemical industry. Adsorption is a widely used technique for the removal of VOCs due to its high efficiency, low cost, and convenient operation. In this study, the feasibility to use a locally available clay, as adsorbent material to control VOCs emissions is evaluated. Natural clay is characterised by different physical-chemical methods and adsorptive interaction features between VOCs and natural clay are identified. Toluene (T), methanol (M) and benzaldehyde (B) are used here as representatives of three different kinds of VOCs. Adsorption isotherms onto natural clay and faujasite-Y type zeolite (Fau Y) are obtained at room temperature. According to Langmuir model data, maximum adsorption capacities (qm) of Fez natural clay and zeolite toward methanol (M), toluene (T) and benzaldehyde (B) at 300 K are 8, 0.89 and 3.1 mmol g–1, and 15, 1.91 and 13.9 mmol g–1 respectively. In addition, the effect of temperature on the adsorption of toluene onto natural clay is evaluated in the range from 300 to 323K. An increase on temperature reduces the adsorption capacity of natural clay toward toluene, indicating that an exothermic physical adsorption process takes place. The enthalpy of adsorption of toluene onto Fez natural clay was found to be –54 kJ mol–1. A preliminary cost analysis shows that natural clay could be used as an alternative low cost adsorbent in the control of VOCs from contaminated gas streams with a cost of US$ 0.02 kg–1 compared to Fau Y zeolite with US$ 10 kg–1.

2016, Dr. Valdes-Morales, Hector, Zaitan, Hicham, Manero, Marie

In this study, a hydrophobic synthetic zeolite, namely ZSM-5 is chosen as an adsorbent/ catalyst for toluene removal. Experimental results showed that toluene adsorption onto ZSM-5 was favourable, following a Langmuir adsorption isotherm model. ZSM-5 zeolite was regenerated using gaseous ozone at low temperature. Adsorbed toluene was oxidised, releasing mainly CO2 and H2O. Traces of oxidation by-products such as acetic acid and acetaldehyde were formed and remained adsorbed after the oxidativate regeneration with ozone. After four successive cycles of adsorption/ozonation, the adsorption efficiency was not affected (92%–99%). These results showed that volatile organic compound (VOC) removal by adsorption onto ZSM-5 zeolite followed by ozone regeneration could be used as a promising hybrid process for the control of VOC emissions in terms of efficiency.

2019, Bencheqroun, Zineb, El Mrabet, Imane, Kachabi, Mohammed, Nawdali, Mostafa, Valdes-Morales, Hector, Neves, Isabel, Zaitan, Hicham

This study aims to evaluate the technical feasibility of applying a low-cost alternative natural bioadsorbent obtained from the cone of the Moroccan cypress Cupressus sempervirens to remove dyes from contaminated waters. Methylene Blue (MB) and Congo Red (CR) dyes are used to represent basic and acid compounds present in wastewater of textile industries. The cone of this medium-sized coniferous evergreen tree was obtained from the Fez area and was characterised by different physical– chemical methods, including nitrogen adsorption–desorption isotherms, Fourier transform infrared spectroscopy, scanning electron microscopy, Boehm titration method and the pH of the point of zero charge (pHpzc). Additionally, the influence of operating conditions such as contact time, initial dye concentration, binary mixture of dye solutions, bioadsorbent dosages and solution pH were evaluated. Experimental results reveal that the adsorption processes take place very rapidly, reaching equilibrium at 30 and 45 min for MB and CR, respectively. Maximum adsorption capacities result to be pH dependents. Hence, MB adsorption is favoured under basic pH conditions, while CR is favoured at acidic pH. A pseudo-second-order kinetic model provides the best fit of the experimental data of MB and CR adsorption onto the biomaterial. Adsorption isotherm data are well represented by Langmuir, Freundlich and Dubinin–Radushkevich models. Langmuir model gives the best fit with a maximum monolayer sorption capacity of 144 and 25.02 mg g–1 for MB and CR, respectively. Experimental results indicate that the cone of Cupressus sempervirens could be used as a potential, low-cost bioadsorbent for the elimination of dyes from contaminated waters.

2017, Dr. Valdes-Morales, Hector, Hadria, Mohamed, Chaouki, Zineb, Draoui, Khalid, Nawdali, Mostafa, Barhoun, Abdeslam, Drouiche, Nadjib, Zaitan, Hicham

This article presents the adsorption of Methylene Blue (MB) onto diatomite, in order to develop a low-cost treatment technology as a process alternative for dye removal. Diatomite used in this work was taken from the Nador area in the northeast of Morocco. Diatomite is characterised by different physical–chemical methods (X-ray diffraction, nitrogen adsorption-desorption isotherm, scanning electron microscopy and Fourier transform infrared). Results showed that the adsorption of MB onto diatomite mineral is affected by various operating parameters like contact time, initial dye concentration, adsorbent dosage, pH and temperature. Adsorption equilibrium is reached after 1.5 h of contact time. Maximum MB removal is obtained at pH = 12. MB removal rate decreases as pH decreases. Adsorption equilibrium data are fitted to Langmuir, Freundlich, Redlich–Peterson and Toth models. Adsorption data are well described by Langmuir isotherm model indicating that a homogeneous adsorption occurs. A maximum adsorption capacity (or monolayer coverage) of 11 mg g–1 is obtained at 45°C. A value of the enthalpy of adsorption of 12.78 kJ mol–1 is found confirming the endothermic nature of adsorption process, while a Gibb’s free energy change (∆G°) falling in the range −30.8 to −35.34 kJ mol–1 confirms the spontaneity of the process. Adsorption kinetics are fitted to a pseudo-second-order kinetic model. Experimental results indicate that the Moroccan diatomite could be used as a potential adsorbent for the removal of cationic dye molecules, at lower cost.