Dra. Azócar-Ulloa, Laura

Copper contamination in watercourses is a recent issue in countries where mining operations are prevalent. In this study, the application of copper precipitation through microbe-induced carbonate precipitation (MICP) was analyzed using urea hydrolysis by bacteria to evaluate precipitated copper carbonates. This article demonstrates the application of a copper precipitation assay involving Sporosarcina pasteurii (in 0.5 mM Cu2þ and 333 mM urea) and analyzes the resultant low removal (10%). The analysis indicates that the low removal was a consequence of Cu2þ complexation with the ammonia resulting from the hydrolysis of urea. However, the results indicate that there should be a positive correlation between the initial urea concentration and the bacterial tolerance to copper. This identifies a challenge in the industrial application of the process, wherein a minimum consumption of urea represents an economic advantage. Therefore, it is necessary to design a sequential process that decouples bacterial growth and copper precipitation, thereby decreasing the urea requirement.

The production of fatty acid methyl esters (FAME) from waste frying oil (WFO) was studied using fly ash as received as a heterogeneous catalyst. The fly ash used in this research had a high content of both CaO and SO3, two compounds that have been previously proposed as catalysts in FAME production. The study was carried out on the basis of a response surface methodology (RSM). The model generated by RSM predicted as optimal conditions to obtain a 100% FAME yield at a methanol-to-oil molar ratio of 3.1:1, 11.2 (wt.% based on oil weight) fly ash and a temperature of 59 C with agitation at 245 rpm and 6 h of reaction time. Additional experiments comparing anhydrous with aqueous medium showed that fly ash presented a high catalytic capacity to transform free fatty acids (FFA) into FAME through consecutive hydrolysis and esterification processes (hydroesterification) compared with that associated with the transesterification mechanism. According to the results, the fly ash used in this study would act as a multipurpose or “versatile” catalyst due to its chemical composition with constituents that act as acidic and basic catalysts, therefore, catalyzing the transesterification and hydroesterification reactions simultaneously and increasing the conversion yields of FAME.

The carbonization of Nannochloropsis gaditana microalgae biomass was found to produce bio-coal that is similar to bituminous coal used in thermal power plants. Currently, microalgae that capture CO2 while they are in the growth stage are considered a source for the production of biofuels. The carbonization of biomass for producing bio-coal has received attention for its ability to improve the biomass quality for producing solid biofuels. The research was focused on optimizing a fixed carbon index (FCindex), which allows finding operational conditions of carbonization to favor the fixed carbon content without significantly affecting the bio-coal yield. The optimization carried out by response surface methodology in a thermogravimetric analyzer allowed the prediction of optimal carbonization conditions to achieve an FCindex of 191% at 403 °C, 71 °C/min, and 60 min of residence time. The bio-coal produced under optimized conditions was characterized by 59% of fixed carbon and 41% of volatiles on a dry and ash-free basis, which is similar to bituminous coal. The promising results of dry carbonization producing bio-coal similar to bituminous coal could promote this technology, avoiding the necessity of hydrothermal carbonization. Because a high ash content was detected in the final product, further studies using the optimized conditions and a washing step should be conducted.

In this study, the torrefaction process was optimized to improve the energy yield (Yenergy) in wheat straw pellet production. Wheat is the main agricultural product of Chile and cultivated in approximately 262 000 ha of land. Additionally, solid biofuel alternatives are necessary in the southern cities of Chile to reduce the pollution produced by low-quality firewood used as fuel. That being the case, it appears that wheat straw is a feasible raw material for solid biofuel production. In the current study, the torrefaction of wheat straw was optimized in a thermogravimetric analyzer using the response surface methodology (RSM). The polynomial model generated from the RSM study showed that heating rate and temperature were significant variables on the response variable, Yenergy; time was insignificant. It was shown that a decrease in temperature of up to 130 °C resulted in an enhancement of the Yenergy value, and at the aforementioned temperature, a low heating rate improved Yenergy. Following the conditions predicted by the model, torrefaction assays were conducted in a bench scale reactor under light torrefaction conditions: a torrefaction temperature of 145 °C, heating rate of 3 °C/min, and final torrefaction time of 50 min. The torrefied biomass was employed in a pellet production process that was performed in a pilot plant facility. The pellet produced from the torrefied biomass under light torrefaction conditions was named “brown pellet” because of its color. Most of the pellet properties satisfy the Standards for Industrial pellets (ISO 17225-6). This showed that light torrefaction temperature can be a potential pretreatment to achieve a commercial production process. Finally, an interesting result was obtained—the bulk density of brown pellets (568 ± 8 kg/m3) was considerably higher compared to that of wheat straw pellets (469 ± 8 kg/m3). This was probably caused by an increment in grinding characteristics. Further studies that focus on identifying the effects of light torrefaction conditions on the mechanical properties of wheat straw pellets should be conducted.

The use of pellets as a replacement for firewood has been promoted in Chile to mitigate atmospheric pollution. However, their high demand has generated stock shortages, which has motivated the search for alternative sources of feedstock. Furthermore, invasive shrubs are a highly available biomass source for bioenergy production in central-southern Chile and may be a significant factor contributing to the spread and increasing virulence observed in wildfires across the region. This study aimed to determine the change in wildfire indicators related to the removal of invasive shrubs in selected zones in the Biobío region and to assess the physicochemical properties of the extracted biomass to develop a pellet formulation to produce a material conforming to ISO standards. The biomass management of Teline monspessulana, Ulex europaeus, and Rubus ulmifolius was evaluated using a fire simulation tool in three areas with contrasting physio-climatic conditions. Our simulation results demonstrated the effectiveness of shrub management on three critical wildfire indicators. Namely, significant decreases were observed in fireline intensity (kW/m) 58–75%, flame length (m) 0–40%, and heat per unit area (kW/m2) 86%. Furthermore, a biomass quality index (BQI) was developed based on the physicochemical parameters of the three shrubs assessed. Based on this BQI, T. monspessulana was selected as the most promising shrub biomass and was consequently used in a pilot shrub-pinewood blending to produce pellets. A blending of 20:80%m/m exhibited properties close to the ISO standard. Our results show that the management of invasive shrubs has the potential to minimize the virulence of wildfires, while the physicochemical characteristics and availability of one of the shrubs analyzed (T. monspessulana) make it a viable alternative biomass source for pellet production in the region.

This study investigated pellets produced using shrub biomass blended with pine sawdust to improve their physical and combustion properties by incorporating additives. First, the properties of pellets produced at different temperatures were analyzed. Pellets produced using pine sawdust blended with Teline monspessulana and Ulex europaeus biomasses (80/20 %m/m) exhibited good properties when prepared at 50–60 ◦C, whereas pellets produced using Rubus ulmifolius exhibited better characteristics at lower temperatures. The results showed that further studies on the physical properties and operational conditions of biomass from Ulex europaeus and Rubus ulmifolius are required. Furthermore, pellets blended with Teline monspessulana were evaluated using starch and lignin as binders, which exhibited all the physical properties of ISO 17225–6 when 1 wt% lignin was added owing to the stronger bonding induced by the additive. Because the fuel indices indicated a high corrosion risk, the additive CaO was used to improve the combustion performance of pellets blended with Teline monspessulana biomass and binders. The content of particulate matter smaller than 2.5 and 10 μm decreased by approximately 50%, and the crystallinity of the bottom ash, which usually contains undesirable elements, was improved by adding 1 wt% CaO, which raised the melting temperature of the ash.

We evaluated the use of hazelnut shell (HS) for pellet production. The investigation of chemical properties, such as the calorific value, low ash, nitrogen, sulfur and chlorine content as well as low heavy metal contents, reveals that the proposed biomass is suitable. However, fuel agglomeration is complicated possibly by some chemical (high content of extractives and lignin) and mechanical properties (spherical shape of particles). Therefore, the blend of HS with pine sawdust is examined in an iterative study, and pellet production is feasible only for percentages of HS lower than 30% in semi-industrial pelleting. The produced pellets exhibit properties compatible to those of industrial and domestic standards; however, as expected the mechanical durability and bulk density needs to be improved. Further studies to identify the optimal operating conditions for the evaluated blend can provide strategies to satisfy the projected increase in pellet demand.

Nowadays, leaves, bark, and branches are generated from the tree-pruning process in urban places, where their management is a problem because of the necessity of disposal. These wastes are lignocellulosic biomasses with poor properties for use in biofuel production, but with interesting projections for building block products such as phenol compounds. Therefore, extensive biomass characterization of urban pruning from Liquidambar styraciflua L. was developed to evaluate its composition as a tool for phenol production through thermal processing, in which solvent extraction is a complementary tool for selectivity improvement. The results showed high lignin content in bark and leaves at 45 and 28 %, respectively, compared with that in branches (14 %). Additionally, high extractives in leaves (14 %) could be an additional source of phenols. The lignin units were analyzed by Raman dispersion, revealing p–hydroxyphenyl (H) units in the bark, guaiacyl (G) units in the bark and leaves, and syringyl (S) units only in the branches. Furthermore, the micropyrolysis coupled with gas chromatography/mass spectrometry assay realized at 600 ◦C showed high presence of phenolic compounds in the three biomass investigated, where a high phenol concentration was identified in leaves, probably due to the S unit degradation during pyrolysis. With these results, an assay for bio-oil production was performed in a low-temperature pyrolysis reactor using leaves as feedstock, reaching a low bio-oil yield with high water content favored for the high inorganic content of leaves (13 %). The produced bio-oil was used for liquid–liquid extraction evaluation, where 1-octanol and methyl isobutyl ketone were identified as interesting solvents for catechol and phenol extraction, respectively. This article presents the challenge of characterizing each part of urban trees, which could be a tool to promote the use of urban pruning by studying the thermal degradation mechanism to implement processes for high-value products, such as phenols produced from L. styraciflua L.

In this study, lignin derived from corncobs was chemically modified by substituting the hydroxyl groups present in its structure with methacrylate groups through a catalytic reaction using methacrylic anhydride, resulting in methacrylated lignin (ML). These MLs were incorporated in polymerization reaction of the monomer 2-[(acryloyloxy)ethyl trimethylammonium] chloride (Cl-AETA) and Cl-AETA, Cl-AETA/ML polymers were obtained, characterized (spectroscopic, thermal and microscopic analysis), and evaluated for removing Cr (VI) and As (V) from aqueous media in function of pH, contact time, initial metal concentrations and adsorbent amount. The Cl-AETA/ML polymers followed the Langmuir adsorption model for the evaluated metal anions and were able to remove up to 91 % of Cr (VI) with a qmax (maximum adsorption capacity) of 201 mg/g, while for As (V), up to 60 % could be removed with a qmax of 58 mg/g. The results demonstrate that simple modifications in lignin enhance its functionalization and properties, making it suitable for removing contaminants from aqueous media, showing promising results for potential future applications.

A Biomass Quality Index (BQI) developed using a previously reported tool was shown to be a promising method to rank biomass suitable for solid biofuel production. The BQI was developed by selecting 12 chemical parameters to be analyzed among ten available biomasses produced in the north, central and south of Chile. Furthermore, a Parameter Quality Index (PQI) was calculated to estimate the contribution of each parameter in the BQI. The sum of all PQIs for each biomass allowed the BQI to be determined, and biomasses with lower BQIs were more highly ranked. The results showed that the first 3 ranks were dominated by biomasses collected in central Chile, hazelnut shell, cherry pits and corn cobs (BQI ≤ 16.1). Furthermore, a promising candidate that was ranked fourth place was wheat straw (BQI = 17.7), which may be able to be used the highly polluted southern zone. Meanwhile, grass and the microalgae N. gaditana were ranked last (BQI ≥ 69.5). The low BQI obtained for the studied biomasses were related to their low PQIs regarding moisture content, low trace element content, low ash percentage and high carbon content and HHV. By contrast, high BQI values were related to high PQIs for moisture, Cl, Na and K content. K had a high contribution and Cu had a low contribution in the index. Due to the difficulty of milling the top ranked biomass, further studies should include a grindability analysis orother physical parameters to complete the BQI methodology.