Dr. Maureira-Carsalade, Nelson

This research assesses the feasibility of recycling copper mine tailings (CMT) by analyzing the durability and mechanical characteristics of cement mortar using these tailings as filler additives. CMT are mineral wastes generated during the process of mining. In this work, specimens of cement mortar were incorporated with up to 30 wt.% of a CMT. Bulk density, dynamic modulus of elasticity, apparent density, ultrasonic pulse velocity, flexural and compressive strengths tests were evaluated. Total amount of voids, sorptivity, water absorption and chemical resistance tests were also obtained to evaluate the mortar durability. When10wt.%CMTwasincorporated, overall amount of voids in the mortar was reduced by 20% and mechanical performance was improved by 16% after 28 days. The flexural strength of the mortar was also found to increase, with the 20% wt.% CMT mortar incorporation reaching a flexural strength of 5.89 MPa. Thus represents 16% increase compared to the control 0% CMT strength. The results indicated that there was not a perfect correlation between these results and the mechanical strength results for the 15and 20wt.% CMT mortars. In addition, the CMT acts as a protective barrier against harmful chemicals. The results of this research indicate that reusing CMT by incorporating into cement mortar is a feasible method for their recycling. Mortar made with as much as 15 wt.% CMT presented the same strength and durability as mortar with traditional sand and cement.

The steel-concrete composite column comprises a steel core and surrounding concrete. The purpose of the system is to provide analysis and design techniques for a newly invented class of laced steel-concrete composite short columns for cyclic axial loads. To minimize the increasing density issues associated with nominal strength concrete and in consideration of the depletion of natural resources required to produce concrete, factory-obtained lightweight sintered fly ash aggregates with and without basalt fiber are employed. The normal-weight concrete containing basalt fiber is shown to be more ductile than any other column. The axial deformation of columns LNA and LSA at failure was found to be 3.5 mm, whereas columns LNAF and LSAF reached an axial shortening of 4.5 mm at failure. The column LSAF was found to have 5.3% more energy absorption than the LSA and 11.5% less than the column LNAF. It was observed that the rigidity of these fabricated components had been enhanced. It was found that the section configuration with a lacing system had improved confinement effects and ductility. Comparing the finite element analysis to the experimental data revealed a strong connection with numerical modeling, with a variance of around 8.77%.

The present study concerns the physico-chemical, structural, mechanical and thermal characterization of Acacia pennata, a natural and almost inexpensive fibre, as a potential reinforcement in polymer composites. The effect of treating the fibre with sodium acetate to increase its qualities has been seen through the use of thermogravimetric analysis, scanning electron microscope (SEM) analysis, X-ray diffraction (XRD), mechanical property tester, and Fourier transform infrared spectroscopy (FTIR). According to XRD analysis, the elimination of lignin and wax-like impurities resulted in an increase in the AP fibre’s crystalline index (79.73%). The fibre’s thermal stability was also discovered to be 365 ◦C. Tensile strength (557.58 MPa) and elongation at break both increased by 2.9% after treatment with sodium acetate. The surface nature and quality of AP fibres improved after sodium acetate treatment. It was confirmed by the reduction of chemical compositions (such as hemicellulose, lignin and pectin). Given its density, the fibre can be suggested as a reinforcement in polymer composites for light-weight applications because its lightweight property will be more useful for composite manufacturing.

Today, new materials based on natural fibres have been emerging day by day to completely eradicate plastics to favour our environmental nature. In this view, the present work is based on the extraction and characterisation of the novel root fibres of the Zea mays (Zm) plant, grown by the hydroponic method. Both the dried untreated and alkali treated root fibres are investigated using a variety of structural, morphological, thermal, elemental and mechanical tests by subjecting both the samples to p-XRD, FT-IR, SEM-EDAX, TGA-DTA, CHNS and tensile strength analyses. Thermal conductivity of the untreated and treated fibres is found using Lee’s disc experiment. From p-XRD analysis, the Crystallinity Index, Percentage Crystallinity and Crystallite size of the samples are found. FT-IR studies clarify the different vibrational groups associated with the fibre samples. SEM images show that the surface roughness increases for the chemically treated samples, such that it may be effectively utilised as reinforcement for polymeric composites. The diameter of the fibre samples is found using SEM analysis. According to the EDAX spectrum, Zm fibres in both their raw and processed forms have high levels of Carbon (C) and Oxygen (O). The TGA-DTA tests revealed that the samples of natural fibre have good thermal characteristics. CHNS studies show that Carbon content is high for these samples, which is the characteristic of many natural fibres. Chemical analysis is used to ascertain the prepared samples’ chemical makeup. It reveals that both samples have significant amounts of cellulose. The density of the fibres is found to be in the range 0.3–0.6 g/cc, which is much less than any other natural fibre. Therefore, it can be used in light weight applications. From the tensile strength analysis, physical properties such as Young’s modulus and micro-fibril angle are determined. The fibres in the roots exhibit a lower tensile strength. Thus, these fibres can be used in powdered form as reinforcement for natural rubber or epoxy composites. After examining all of its properties, it could be reasonably speculated that Zea mays root fibres can be considered as an efficient reinforcement for various matrices to produce attractive bio-composites.

Natural fiber (NF) is one of the many resources that nature has provided. NFs decompose quickly and are biodegradable, renewable, and cost-effective. It may be scavenged from a variety of plant and animal sources. They are employed as reinforcing materials in polymers for NF composite development. Because of its environmental friendliness and long-term survivability, NF is growing in appeal among academics and researchers for usage in polymer composites. This study aims to offer a thorough evaluation of the most suitable and widely utilized natural fiber-reinforced polymer composites (NFPCs), along with their manufacture, processing, and applications. It also defines several external treatments of NF and their influence on the characteristics of NFPCs. The characteristics of NFPCs are affected by fiber supply, fiber type, and fiber structure. Numerous physical and chemical treatments were tested to see how they affected the thermal and strength properties of natural fiber-reinforced thermoplastic and thermosetting composites. Several polymer composite fabrication techniques were also studied. NFPCs have several disadvantages, notably low fire protection, poor strength properties, and greater moisture absorption, which have prevented their application. It is shown how NFPCs are employed in a variety of industries, particularly automotive and research industries. The review discovered that intentionally changing the regular fiber enhanced the thermochemical and physico-mechanical properties of the NFPCs by means of improving the grip between the fiber surface and the polymer framework. This study aims to provide important and fundamental facts on NF and their composites, which will aid in new investigations, the creation of a creative framework for polymer composite types, and the achievement of Sustainable Development Goals.