Dr. Maureira-Carsalade, Nelson

Introducción: el contacto con la naturaleza es fundamental para la salud física y mental de las personas, especialmente en estudiantes universitarios. Sin embargo, este vínculo se ha ido perdiendo en las últimas décadas debido al crecimiento de las ciudades. El objetivo de este estudio fue comparar el nivel de contacto directo con el medio natural en estudiantes universitarios chilenos según la zona geográfica donde habitan. Métodos: se realizó una investigación cuantitativa con un diseño descriptivo analítico. Participaron 272 estudiantes de 6 universidades chilenas ubicadas en diferentes zonas geográficas (norte, centro y sur). Se aplicó la escala de contacto con la naturaleza de manera online. Se utilizó la prueba de Kruskal-Wallis para determinar diferencias significativas entre las distribuciones de respuesta según zona geográfica. Resultados: los estudiantes de la zona central reportaron mayor contacto con la naturaleza en su vida cotidiana (45,40 % en niveles 4-5). En excursiones, los del sur lideraron (45,16 % en niveles 4-5). En actividad física, los del sur también presentaron los mayores porcentajes (58,06 % en niveles 4-5). Se encontraron diferencias significativas entre zonas en todas las dimensiones (p<0,05). Conclusiones: en general, los estudiantes presentan un bajo contacto con entornos naturales, siendo los de la zona norte quienes reportan los niveles más bajos. Esto evidencia la necesidad de incluir más áreas verdes en las instituciones educativas, especialmente en el norte y grandes ciudades, para fomentar el vínculo con la naturaleza y sus beneficios en la salud y desarrollo de los estudiantes.

Se presentan resultados de ensayos de conexiones de momento viga-columna de racks de almacenamiento. Se realizaron ensayos cuasi-estáticos usando un actuador electromecánico controlado por desplazamiento a conexiones con dos diferentes torques de apriete de pernos. El montaje experimental contempla una columna 1.48 m de largo, rotulada en sus dos extremos, y una viga de largo 1.72 m. El actuador cuenta con una celda de carga de 900 kg de capacidad en su extremo de conexión con la viga y registra ladeformación aplicada mediante un sensor de desplazamiento de recorrido de 300 mm. La viga fue instrumentada con sensores de giro, disponiendo uno justo antes del apoyo, y dos en el perfil L que la conecta con la columna. El forzante corresponde a secuencias de desplazamiento cíclico tipo serrucho con amplitudes crecientes, adaptada del AISC341 (2022) sección K. Los resultados mostraronque, al incrementar el torque de 54.2 Nm a 108.5 Nm, la rigidez elástica se incrementó en un 45%. Un mayor torque de apriete generó reducción en el pinching y aumento en la energía disipada de la conexión, en comparación al caso con menor torque. En general, las conexiones fueron capaces de resistir rotaciones de hasta 0.07 rad.

This research assesses the feasibility of recycling copper mine tailings (CMT) by analyzing the durability and mechanical characteristics of cement mortar using these tailings as filler additives. CMT are mineral wastes generated during the process of mining. In this work, specimens of cement mortar were incorporated with up to 30 wt.% of a CMT. Bulk density, dynamic modulus of elasticity, apparent density, ultrasonic pulse velocity, flexural and compressive strengths tests were evaluated. Total amount of voids, sorptivity, water absorption and chemical resistance tests were also obtained to evaluate the mortar durability. When10wt.%CMTwasincorporated, overall amount of voids in the mortar was reduced by 20% and mechanical performance was improved by 16% after 28 days. The flexural strength of the mortar was also found to increase, with the 20% wt.% CMT mortar incorporation reaching a flexural strength of 5.89 MPa. Thus represents 16% increase compared to the control 0% CMT strength. The results indicated that there was not a perfect correlation between these results and the mechanical strength results for the 15and 20wt.% CMT mortars. In addition, the CMT acts as a protective barrier against harmful chemicals. The results of this research indicate that reusing CMT by incorporating into cement mortar is a feasible method for their recycling. Mortar made with as much as 15 wt.% CMT presented the same strength and durability as mortar with traditional sand and cement.

The objective of this study was based on the application of the response surface methodology (RSM) for yield optimization in maize (Zea mays L.). The hybrid INIA SQ-1 was used, and the Response Surface Methodology was used using the Box-Behnken design (DBB), with which the following factors were evaluated: plant density, nitrogen (N) dose and phosphorus (P) dose at three levels each; for the optimization of the response variables: “yield” (kg.ha-1) and the “number of grains per square meter” (g.m2). The response surface method provided a statistically validated predictive model, which through adjustments was adapted to an established optimization process. For the variable “yield”, a maximum response was found with the application of 150 Kg.ha-1 of N and 90 kg.ha-1 of P. In relation to the number of grains per square meter (g.m2), the optimum was obtained using 75,000 plants.ha-1 and an applied dose of 150 kg.ha-1.

An improved numerical formulation for a self-centering frictional damper is presented. This was experimentally validated through quasi-static tests carried out on a steel-made prototype of the damper. Its design is ad hoc for implementation in the seismic protection of industrial storage racks. The conceptual model of the device was adjusted to the prototype built. The formulation of the analytical model, a parametric analysis of it, and the validation with experimental results are presented. The improvement of the model presented here explicitly considers elements included in the prototype, such as a system of load transmission rings and the friction between all of the components that slide or rotate relatively. In the experimental validation, the parameters of the improved model were determined. The numerical predictions for the improved model were contrasted with those obtained with the original one and with the experimental results. This demonstrates that the improvement leads to a better adjustment of the numerical predictions concerning the experimental measurements, which is useful for nonlinear analysis. The device withstood forces of considerable magnitude in addition to dissipating enough energy per load–unload cycle to be effective in the seismic protection of industrial storage racks.

The behavior of the web panel zone has a direct effect on the cyclic performance of steel moment connections. While the mechanisms of web panel zone failure are known under cyclic load, little is known about the behavior of the web panel zone under bidirectional loads in bolted connections. Using experimental tests and calibrated numerical models, this research evaluated the web panel zone behavior under unidirectional and bidirectional cyclic loads. The results showed that bidirectional load can modify the stress and strain distribution in the web panel zone. Moreover, the increasing of the width-to-thickness ratio of the column influences the failure mechanism of the joint configuration and increases the plastic incursion in the column. These data demonstrate that bidirectional effects improve the web panel zone performance under cyclic loads.